#PHOTO TO MOVIE 4.2.7 INSTALL#
#PHOTO TO MOVIE 4.2.7 DRIVER#
#PHOTO TO MOVIE 4.2.7 UPGRADE#
#PHOTO TO MOVIE 4.2.7 PRO#

Whether you are using it for gaming or creating ordinary YouTube videos. What are you planning to use it for?: You must know the use of video editing software before picking one. But you don’t have to worry about it anymore let’s begin: I rearranged the wiring from red/blue/yellow to blue/red/yellow as suggested by 3D4LYF again because I am using the BLTouch Creality Kit.05 Related FAQs about Free Video Editors Part 1: Things to Consider When to Choose a Free Video Editorīefore opting for a free video editing software there are many important things, we mostly miss that we should have known.

For the three wires on the black connector I have: blue=Ground, red=V, yellow=IN that goes in the other 5 pin port on the mainboard. The two wires (white & black) on the red connector go in the Z-axis endstop port on the mainboard. I'm using 3D4LYF's wiring scheme as I'm using the same set up I believe he is using. BLTouch lights up and the sensor tip moved in and out as if it was checking something or verifying it was working.

#PHOTO TO MOVIE 4.2.7 INSTALL#

Position after install of BLTouch: remained the same. I just remember it powering on ok and then I turned it off / unplugged power to start installing the BLTouch. Position after install mainboard upgrade: remained the same as before. Position of the print head before install: 3-4 inches above the bed and maybe a little off-center on the X-axis. If helpful, here are the positions of the nozzle head during the two upgrades : I attempted to follow step #6 Platform adjustment 32-bit, working through the screenshots in the instructions. Now, when I hit auto home the nozzle head moves like I described above & remains in a position that I can not attempt to print from. The BLTouch lights up and the touch sensor clicks out and in and few times. The firmware I upgraded to is the Ender-3 Pro_4.2.7_BLTouch_Marlin2.0.1_V1.1.2_TMC2225.bin.įinally, I powered on the printer with the BLTouch plugged in and new firmware installed. Here, I upgraded the firmware via an SD card as suggested. I followed the instructions for the Creality V1 Mainboard 32-bit. Next, I followed the instructions for the BLTouch that came with the kit. The nozzle head did not move I don't think when powered on. The only thing I did here was to verify that the printer would power up ok. It is totally disconnected and leftover from the BLTouch install.įirst, I simply replaced the new mainboard, and with the mainboard cover and fan back in place, I powered the printer on. Note: Disregard the unhooked cable under the printer bed in the video. Here's a video of the printer attempting to Auto Home : The new board is 32-bit and not sure what that would negatively impact besides maybe the LCD screen which does work fine after the upgrade. I assume it came with an 8-bit board but not 100% sure. It was working great until I decided to make the upgrades.

#PHOTO TO MOVIE 4.2.7 PRO#

I purchased this Ender 3 Pro back in April 2020.

#PHOTO TO MOVIE 4.2.7 UPGRADE#

I imagine I attempted too many upgrades without verifying the printer worked properly when I did the first upgrade which was the mainboard?

#PHOTO TO MOVIE 4.2.7 DRIVER#

I installed a Creality Ender 3 Pro New Upgrade Motherboard Silent Mainboard V4.2.7 with TMC2225 Driver Marlin 2.0.1 & bootloader pre-installed & then a Creality BLTouch 3D Printer Upgraded Auto Bed Leveling Sensor Kit (the kit that comes from Creality with everything you need to install). It does not move at all on the Z-axis and remains 3 - 4' above the bed during and after Auto Homing. After I Auto Home, it moves along the X-axis to the left, hits the stop switch & moves back to the right. I made two updates to my Ender 3 Pro: Silent Mainboard and BLTouch.

Photo to movie 4.2.7